Skip to content

Free roof inspection and a straight read on years left: (317) 836-2367

Avon · Plainfield · Brownsburg · Danville

(317) 836-2367

ServicesMetal Roofing

Metal Roofing in Avon, IN

A metal roof costs more on day one than shingles. It can also outlast two or three shingle roofs and needs little upkeep. We lay out both sides in plain terms, then install standing seam or panel roofs built to handle snow, wind and summer heat.

Roofer in a yellow safety harness kneels on underlayment, fastening a standing-seam metal roof panel with a cordless drill beside finished gray panels on a house

When a metal roof makes sense

Metal is a good fit when you plan to stay in your home a long time. The panels shed snow, stand up to wind and don't curl or lose granules the way asphalt does. A well-installed standing seam roof can go for decades with not much more than a look after big storms.

It is not the right call for everyone. If you might sell in five years, a good shingle roof often gives you more for your money, and we will say so. Our Shingle Roofing page covers that side of the choice.

We have been in business for 14 years. What we've seen in that time is that the details decide how long metal lasts: the underlayment, the trim at walls and valleys, and fastening the panels so they can move as they heat up and cool down.

Roofer in a yellow safety harness kneels on an asphalt shingle roof, lifting a loose shingle while holding a clipboard, with a ladder and trailer below.

What's part of every metal roof we install

  1. 01

    Old roof stripped to the sheathing

    The existing roofing comes off first so we can see the sheathing. Any soft or rotted plywood is cut out and replaced before new materials go on, and we photograph what we find to show you.

  2. 02

    Underlayment rated for metal

    Metal gets very hot in summer sun, so the underlayment has to handle that heat. We add ice and water shield at the eaves and in the valleys, where winter ice dams push water back up.

  3. 03

    The panel system you choose

    Standing seam keeps fasteners out of sight and lets panels move as temperatures change. Exposed-fastener panels cost less to start, but their rubber washers wear out and need checking and replacement over time. We walk through that trade-off so the choice holds up years from now.

  4. 04

    Flashing, trim and attic vents

    We cut flashing to fit each chimney, sidewall, skylight and pipe. We also check ridge and attic vents so heat and moisture can escape.

  5. 05

    Snow guards above entries and paths

    Snow comes off metal all at once. Guards over doors, decks and walkways stop it from landing on people or crushing your plantings.

  6. 06

    Cleanup and a final walk with you

    We run a magnet bar over the yard and driveway for loose screws and metal scraps and haul away all debris. Then we go over the finished roof with you.

Questions about Metal Roofing?

Call(317) 836-2367

When it's worth pricing a metal roof

  • Your second shingle roof is wearing out

    If you've replaced shingles before and they're failing again, get a metal price. Paying once for a roof that lasts longer can cost less over time than paying twice.

  • Ice dams bring leaks every winter

    Snow slides off metal sooner, so less ice forms along the eaves. Combined with good attic ventilation, that reduces the winter leaks that mark ceilings.

  • Wind keeps tearing shingles loose

    When each spring storm drops shingle tabs in your yard, interlocking metal panels will stay down better than loose shingle edges.

  • Rust or loose screws on an older metal roof

    Screws that back out, washers that crack and rust at the overlaps all let water through. New fasteners and sealant sometimes add years, and sometimes the panels are finished. We'll let you know which.

  • You're staying for the long haul

    The more years you live in the house, the more of a metal roof's life you get to use.

How a metal roof job goes

  1. 1

    Free roof inspection

    We go up on the roof and into the attic, measure and take photos. Then we tell you straight whether metal suits your home and your plans, or whether shingles are the better buy.

  2. 2

    Written estimate with every line shown

    It lists panel type, gauge, color, trim, underlayment and an allowance for deck repairs. We pull the permit when the town calls for one. If paying all at once doesn't work, we offer financing.

  3. 3

    On the roof

    We strip and dry in one section at a time, so nothing is left open overnight. Panels and trim are measured and cut for your roof, which means most jobs run a few days. We keep your driveway open where we can and give you a quick update each morning.

  4. 4

    Walkthrough and records

    We look over every seam, flashing and fastener with you. You get your warranty paperwork and photos of the finished roof to keep.

Where the money goes on a metal roof

A metal roof takes a bigger check to install than asphalt. The better way to judge it is what you pay for each year the roof lasts, plus the upkeep you'll have along the way. Every line on your estimate is spelled out, so you can set it next to a shingle price and compare.

Standing seam or screw-down panels
Standing seam uses more material and more hours to install than exposed-fastener panels. In return, there are no screws sitting in the weather, so there's little to reseal over the years.
How cut up the roof is
Every valley, hip, dormer and skylight needs its own trim, bent and fit by hand. A plain two-sided roof goes faster and costs less per square. Steep roofs take longer and need more fall protection.
Metal thickness and finish
Heavier gauge panels stand up to dents better and cost more. The paint finish and color you pick nudge the number a bit too.
Condition under the old roof
More old layers to strip and soft sheathing to swap out both raise the cost. Nobody can see the whole deck until the old roof is off, so we list deck work as an allowance on your estimate.

Metal roofing questions we hear most

Will rain be loud on a metal roof?

Quieter than most people think. The panels rest on solid sheathing and underlayment, with attic insulation below that. From inside the house, most owners say rain sounds about like it does on shingles.

Does hail damage metal roofing?

Big hail can dent panels, and thin panels dent sooner. Most dents are only cosmetic and don't lead to leaks, and a thicker gauge helps. After a rough storm we work with homeowners and insurance companies on storm damage claims. Our Storm Damage Repair page covers how that works.

Can metal go on top of my existing shingles?

Sometimes code permits it, but we seldom recommend it. The old roof covers the sheathing, so any rot keeps growing out of sight. A tear-off costs more today and gives the metal a sound surface to sit on.

How is a metal roof warrantied?

Labor carries a 2-year warranty that can be upgraded to 10 years through Owens Corning. When we review your estimate together, we'll explain which upgrade fits your roof.

Does metal make a house hotter in summer?

Generally the reverse. Metal bounces back more sunlight than dark shingles, light colors most of all, and sheds heat quickly once the sun goes down. Attic ventilation matters just as much, and we check it on every job.

Will my HOA approve a metal roof?

Lots of neighborhoods set rules on roof material and color, so read your HOA guidelines before deciding. We can supply panel specs and color samples for your approval request.

Brick ranch house with a dark brown shingle roof, ladder against the eave, tarp and supplies on the driveway, and a green front lawn under high clouds

See whether metal suits your roof

We'll check your roof and attic, show you what turns up and compare metal with shingles for your house in plain numbers. No pushing in either direction.